MENÜ
-
Insert gates
-
Heatlock hot-runners
-
Servo system components
-
Mold accessories
The chart shows the shot weights which can be reached with the respective sizes depending on the viscosity of the plastic materials used.
| TPS-S | TPS-1 | TPS-2 | TPS-3 | |
| gate point | 0,4 - 0,8 | 0,8 - 1,8 | 0,8 - 2,8 | 1,1 - 4,5 |
| NV * | 30 | 120 | 600 | 1800 |
| MV * | 20 | 75 | 350 | 1000 |
| HV * | 12 | 50 | 175 | 600 |
* max. shot weights (g)
NV: low viscosity
MV: medium viscosity
HV: high viscosity
| b | b1 | b2 max. | d3 | h | h1 max. | h3 | l1 | l2 | l3 | M | |
| TPS-2 | 15 | 6 | 2,4 | 4 | 18 | 4 | ~7 | 6 | 7.1 | 5.5 | 4 |
| TPS-1 | 18 | 8 | 2,6 | 6 | 22 | 5 | ~9 | 6 | 8.4 | 6 | 4 |
| TPS-2 | 25 | 10 | 5 | 8 | 22 | 6 | ~11 | 6 | 11.8 | 7.5 | 5 |
| TPS-3 | 30 | 12 | 6,5 | 10 | 22 | 7 | ~13 | 6 | 14.1 | 8 | 5 |
| A [mm²] | ~ Ø [mm] | b2 [mm] |
| 0.12 | 0.4 | 2.1 |
| 0.40 | 0.7 | 2.2 |
| 0.75 | 1.0 | 2.3 |
| 1.13 | 1.2 | 2.4 |
| A [mm²] | ~ Ø [mm] | b2 [mm] |
| 0.49 | 0.8 | 2.2 |
| 0.92 | 1.1 | 2.3 |
| 1.42 | 1.4 | 2.4 |
| 1.97 | 1.6 | 2.5 |
| 2.56 | 1.8 | 2.6 |
| A [mm²] | ~ Ø [mm] | b2 [mm] |
| 0.54 | 0.8 | 4.2 |
| 1.05 | 1.2 | 4.3 |
| 1.64 | 1.5 | 4.4 |
| 2.3 | 1.7 | 4.5 |
| 3.0 | 1.9 | 4.6 |
| 3.76 | 2.2 | 4.7 |
| 4.55 | 2.4 | 4.8 |
| 5.37 | 2.6 | 4.9 |
| 6.23 | 2.8 | 5.0 |
| A [mm²] | ~ Ø [mm] | b2 [mm] |
| 1.0 | 1.1 | 5.2 |
| 1.81 | 1.5 | 5.3 |
| 2.7 | 1.9 | 5.4 |
| 3.67 | 2.2 | 5.5 |
| 4.7 | 2.4 | 5.6 |
| 5.78 | 2.7 | 5.7 |
| 6.92 | 3.0 | 5.8 |
| 8.09 | 3.2 | 5.9 |
| 9.3 | 3.4 | 6.0 |
| max. 15.8 | 4.5 | 6.5 |
| flexible materials | rigid materials | |
| TPS-S | ~ 18 | ~ 23 |
| TPS-1 | ~ 22 | ~ 30 |
| TPS-2 | ~ 28 | ~ 38 |
| TPS-3 | ~ 33 | ~ 47 |
Side gating - standard installation
Side gating - for flat contours
Side gating - for deep contours
